Georgia Institute of Technology researchers have developed a paper-based flexible supercapacitor using a simple layer-by-layer coating technique that could be used to help power wearable devices. The device uses metallic nanoparticles to coat cellulose fibers in the paper, creating supercapacitor electrodes with high energy and power densities – and the best performance so far in a textile-based supercapacitor.

By implanting conductive and charge storage materials in the paper, the technique creates large surface areas that function as current collectors and nanoparticle reservoirs for the electrodes. Testing shows that devices fabricated with the technique can be folded thousands of times without affecting conductivity.

Image shows that the flexible metallized paper developed in this research retains its conducting properties even when crumpled and folded. Image Credit: Ko et al, Georgia Tech.

Seung Woo Lee, an assistant professor in the Woodruff School of Mechanical Engineering at the Georgia Institute of Technology said, “This type of flexible energy storage device could provide unique opportunities for connectivity among wearable and internet of things devices. We could support an evolution of the most advanced portable electronics. We also have an opportunity to combine this supercapacitor with energy-harvesting devices that could power biomedical sensors, consumer and military electronics, and similar applications.”

The research, done with collaborators at Korea University, was supported by the National Research Foundation of Korea and reported September 14 in the journal Nature Communications.

Energy storage devices are generally judged on three properties: their energy density, power density and cycling stability. Supercapacitors often have high power density, but low energy density – the amount of energy that can be stored – compared to batteries, which often have the opposite attributes. In developing their new technique, Lee and collaborator Jinhan Cho from the Department of Chemical and Biological Engineering at Korea University set out to boost energy density of the supercapacitors while maintaining their high power output.

The researchers began by dipping paper samples into a beaker of solution containing an amine surfactant material designed to bind the gold nanoparticles to the paper. Next they dipped the paper into a solution containing gold nanoparticles. Because the fibers are porous, the surfactants and nanoparticles enter the fibers and become strongly attached, creating a conformal coating on each fiber.

By repeating the dipping steps, the researchers created a conductive paper on which they added alternating layers of metal oxide energy storage materials such as manganese oxide. The ligand-mediated layer-by-layer approach helped minimize the contact resistance between neighboring metal and/or metal oxide nanonparticles. Using the simple process done at room temperatures, the layers can be built up to provide the desired electrical properties.

“It’s basically a very simple process,” Lee said. “The layer-by-layer process, which we did in alternating beakers, provides a good conformal coating on the cellulose fibers. We can fold the resulting metallized paper and otherwise flex it without damage to the conductivity.”

Though the research involved small samples of paper, the solution-based technique could likely be scaled up using larger tanks or even a spray-on technique. “There should be no limitation on the size of the samples that we could produce,” Lee said. “We just need to establish the optimal layer thickness that provides good conductivity while minimizing the use of the nanoparticles to optimize the tradeoff between cost and performance.”

The researchers demonstrated that their self-assembly technique improves several aspects of the paper supercapacitor, including its areal performance, an important factor for measuring flexible energy-storage electrodes. The maximum power and energy density of the metallic paper-based supercapacitors are estimated to be 15.1mW cm2 and 267.3 Wh cm2, respectively, substantially outperforming conventional paper or textile supercapacitors.

The next steps will include testing the technique on flexible fabrics, and developing flexible batteries that could work with the supercapacitors. The researchers used gold nanoparticles because they are easy to work with, but plan to test less expensive metals such as silver and copper to reduce the cost.

During his Ph.D. work, Lee developed the layer-by-layer self-assembly process for energy storage using different materials. With his Korean collaborators, he saw a new opportunity to apply that to flexible and wearable devices with nanoparticles.

“We have nanoscale control over the coating applied to the paper,” he added. “If we increase the number of layers, the performance continues to increase. And it’s all based on ordinary paper.”

The desire and demands for more electrical energy storage continues with gathering intensity. This technology may offer a very cost effective solution, but only for a time as the demand will increase in any case. The technology is still in the lab, but this team has a very short list to cover before trying for going up in scale. Good Luck team, we’re rooting for you.


Comments

3 Comments so far

  1. Waste Sorting Machine on October 11, 2017 8:12 PM

    Paper is really useful. Nowadays many people pay less attention to the paper. however, its function is great.

  2. Palm kernel shell charcoal on October 15, 2017 9:41 PM

    Good idea to make use of paper. Thanks for sharing.

  3. Asphalt on October 16, 2017 2:00 AM

    The paper can be made into super capacitors.Great invention.

Name (required)

Email (required)

Website

Speak your mind

css.php